new here and to model trains

W

Wyndigo

New Member
Jan 25, 2004
15
0
1
Dover, Florida, USA.
Hi everyone, I am new to the model railroad hobby, went to my first train show this past saturday and bought an Athearn HO set, now I have added 4 more 9" sections of track and would like to add a switch onto the setup. Now my question is this, exactly how do they work? (no laughing sign1 ) I'm thinking of a basic layout, small town on one side and a
business of some sort on the other. therefore the need for a switch.

Wyndigo
 
:wave: Welcome to the Gauge! :wave:

Hope to see more questions from you Wyndigo, because for the most part, we have the answers!

Ok, here's a diagram. The red and blue lines are opposite rails, ok? now the switch has movable points (two of them, they move in unison with a small strip of metal holding them together called a switch rod) ? Now those movable points come into position, determining which way the train travels, and with the flick of a switch, you can send the train down a different set of rails to it's destonation. Got it?
 

Attachments

  • Switchdiagram.JPG
    Switchdiagram.JPG
    14.2 KB · Views: 189
Shaygetz: thanks for the welcome and I'm near Tampa for now, planning to move north to michigan before next winter (yeah I know, kinda crazy lol)

MilesWestern: thanks for the welcome and yep, I kinda understand what it does, but how hard is it to hook up, I'm using eztrack with the athearn engine and cars

Wyndigo
 
webmaster said:
Wyndigo it's easy. It just goes together like any other section, you just push fit it on to the next piece of track.
Click to expand...
MMMMMM it's easy is it .lol.
 
Hi Jim and thanks for the welcome :)
lol ok Webmaster & Tonyevans, is it easy or not? gotta remember, I'm new to this and trying to keep it simple .. as in rather not have to solder, even though I can .. was into RC trucks for awhile. anyways, thanks :)

Wyndigo
 
Not sure exactly what you're asking. How do switches work? How do they connect? Since I don't know what track you have, I'll be general. There are essentially two type of turnouts, selective and non-selective. Selective routes power only to the track path that you have chosen. This can be great for sidings and not require a power on-off electrical switch for that siding.

The other type powers both legs of the turnout at all times. Atlas is the most common brand of this type. If you want to shut off the power to a siding using this type of turnout, you will need an on-off electrical switch. Both types require insulated rail joiners to work effectively.

Then there are manual turnouts where you 'throw the switch' and powered turnouts that use 'switch machines' to throw the turnout. There are twin coil machines that go clunk when you press a button and slo-motion machines that remain powered all of the time to hold the points against the fixed rail.

I would suggest that as a new modeler, you might get some useful information from the NMRA 'Introduction to Model Railroading' pages at: http://www.nmra.org/beginner/
 
Yes Wyndigo it is easy. You do not need to solder the track together, just use the fish plates* that you connected the rest of your track together with. (*I presume their called the same the other side of the pond?)

As Roger says, if you want to keep the soldering to a minimum, then choose the ones that are powered no matter which way the switch is. All switches can be thrown by hand so you don't have to worry about switch motors at this point if your happy throwing your switches manually.
 
Wyndigo....

wyndigo said:
but how hard is it to hook up, I'm using eztrack with the athearn engine and cars
Click to expand...

You said that you are using the Bachmann EZ Track. There are switches (turnouts) made in this line as well. They go together like any other section of the EZ Track. With any kind of sectional track (like the EZ Track, or Atlas "snap track") you will be limited in the geometry of your layout. If the pieces end up too far apart when you try to close the loop, you will have to reconfigure, rather than just forcing it...

Take a look at the Bachmann website (or the Atlas one for that matter) to see if there are plans that use sectional track that appeal to you.

Andrew
 
Unless I missed it , nobody mentioned good ol' Atlas snap switches. These little honeys have their own "motor" with a simple three wire activator. If the wire that comes with it isn't long enough use telephone wire. They are quite robust but will Melt if you get a short (don't ask) Welcome, have fun
 
Hi everyone :wave: I bought a switch today along with a little more track, now I have an oval with an inside turnout, thinking of maybe building either a small train station or work place to add to my layout.
Thanks to everyone for the welcomes and the quick answers, I'll be asking more soon :D
for now I'm just having fun with the set and looking up information on how to add scenery.
Take care everyone

Wyndigo
 
Relic said:
Unless I missed it , nobody mentioned good ol' Atlas snap switches. These little honeys have their own "motor" with a simple three wire activator. If the wire that comes with it isn't long enough use telephone wire. They are quite robust but will Melt if you get a short (don't ask) Welcome, have fun
Click to expand...

I saved my burnt out motor. the coil was melting through the bottom
 
Welcome aboard Wyndigo and I can assure you that if you have any questions, just ask here and some of the engineers here will give you the information..I am also a newbie here and by me asking questions and getting advice from the pros here has helped me starting my first layout. Just ask and you will receive answers to your questions.
 
hi everyone again :wave: well, now I have an oval with an inner loop that reconnects to the main track which is now about 6 x 4 in size.
now to start working on some scenery... little at a time, any ideas on making cardboard buildings? Thanks again for all of the replys

Wyndigo aka Alan
 
Take a look in The Academy for "Robin at his Best" - many of his buildings were built exclusively with cardboard from cereal boxes ("cerealboard"). Lots of people use cardboard mock-ups for planning purposes and stand-ins until the kits are done, but Robin took it to a whole new level...

Link in my signature.

Andrew
 
You must log in or register to reply here.
Top Bottom